Troubleshooting
Start with three checks: confirm the selected drone, read the exact on-screen status, and avoid repeating an action while it is still in progress.
Cannot sign in
- Return to the normal Suite address, not a temporary sign-in link.
- Check the account email and keyboard layout.
- Ask a SABROBOTIX Administrator for a temporary password, then replace it at first sign-in. A customer Client can also ask the Operator managing that customer to issue it through the Client account flow.
- Ask an Administrator to confirm that the account exists and has the correct role.
- If a role was just changed, sign out completely and sign in again.
Drone does not connect
- Confirm the correct drone name and serial number.
- Read the status in the Flight data panel.
- Confirm that the drone and its communications equipment are powered.
- Check SIM usage on the drone's Connectivity tab and the expected mobile coverage.
- Read the diagnosis line in Flight data: it says whether the Suite session, the Suite, the drone's gateway or the autopilot is the problem.
- The Suite retries on its own, spacing the attempts out while the drone stays unreachable. There is nothing to press.
- If the drone is not in the list, it is not your company's, or its remote access is off, or its onboard computer is not enrolled.
- If it reports that the onboard gateway may be offline, contact the responsible operator or support.
Telemetry is unavailable or stale
Live telemetry in the current Suite interface is available only to Administrators and Operators. A Client account also encounters the current telemetry-dependent video-launch limitation; reconnecting or changing camera sources does not enable live telemetry for that role.
- Wait until status is Connected.
- Confirm that values continue changing and are not frozen.
- Check the drone’s communication and autopilot state using the approved independent method.
- The Suite retries automatically; there is no reconnect button.
- Do not use mission or flight actions until current position and flight state return.
If telemetry drops during a command, the Suite disables or cancels affected controls. Follow the aircraft’s lost-link procedure.
Map or marker does not appear
- Confirm that position and GPS information are available.
- Wait for the map tiles to load.
- Check the browser’s internet connection.
- Switch map layer once if the current layer fails.
- A missing Home marker means the Suite has not received a valid Home position.
The Suite does not require browser location permission to show the drone’s reported position.
A grey marker remains after the connection drops
Grey markers show an offline or recorded position. They are useful for locating where a drone was last seen, but do not establish its current location. Select the correct drone and check its link status, telemetry age, and GPS fix. A drone without a usable current or previous position has no marker. See Live and last-known positions.
Connected stations is unavailable
Read the message in the drone's Connectivity → Connected stations. An empty list and an unavailable list have different meanings: an unavailable or failed request cannot establish that nobody is connected. The list refreshes while the tab is open. It never includes radio stations and does not give exclusive control. See Check connected stations.
Parameters are missing or look outdated
- Select the correct drone and restore connected, current telemetry before starting a request.
- Open Parameters, clear the search, and check whether the panel reports a value count or a failure.
- Select Read again to fetch a fresh set; reopening the panel can reuse values already fetched during this page session.
- Wait for the value count before treating a saved file as a complete set. A running or failed request may leave only some values available.
The Suite displays parameters in read-only mode; editing the exported .params file does not change the aircraft. See Download and inspect parameters.
A mission file is refused
Replace in the Mission panel expects a QGroundControl-compatible .plan file, such as one from Save .plan or your mission-planning tool. See Replace the mission.
Mission controls are unavailable
Check that:
- your role is Administrator or Operator;
- the correct drone is connected;
- no upload, download, or flight command is already running;
- Start mission has a confirmed downloaded mission and the aircraft is armed;
- Go Here has a supported multirotor, current GPS position, altitude, armed state, and confirmed airborne state;
- RTL has a connected aircraft confirmed airborne;
- Resume mission follows a qualifying interruption and the mission has not changed.
Upload fails
- Use a QGroundControl-compatible
.planfile no larger than 1 MB. - Keep the plan within the limit of 1,000 mission items.
- Validate the plan in the planning tool.
- Keep the drone connected and do not change selection.
- If the drone disconnects or upload times out, treat the aircraft’s stored mission as unconfirmed and download it again before flight.
Stream does not open
- Confirm the selected drone and that remote access is enabled. The current camera launcher requires connected telemetry; a Client account cannot establish that telemetry link.
- Select the camera's named button in Drone Control, or open Cameras on a narrow screen. If the button is disabled, read the video-launch limitation. If it is missing, ask an Administrator or Operator to check the source in Drones → select a drone → Streams.
- Wait for the onboard camera to publish.
- Stop and start that stream once.
- Test another configured stream, including FPV when available.
- Check SIM usage and connection quality.
No video signal or Stream unavailable usually means the configured camera is not publishing usable video. Report the drone, camera slot, time, and exact message.
Video is delayed
- Reduce other traffic on the same connection.
- Close any unused camera players, including detached windows.
- Keep only one viewer when testing.
- Compare telemetry timing with video timing.
- Never use delayed video as the only basis for obstacle avoidance.
External video window does not open
Allow pop-ups for the trusted Suite address, then try Open stream in new tab again. Do not allow pop-ups globally.
A document or maintenance attachment is missing
- Confirm the selected drone and clear the document search.
- For a maintenance attachment, open the correct maintenance history row: attachments are listed inside that record, separately from the drone's main Documents tab.
- If you are a Client, ask staff to check Client access. An uploaded file is not automatically shared with Client accounts; you can also see documents you uploaded yourself.
- Only PDF files have a browser preview. DOCX files download instead.
- If uploading fails, confirm the format is PDF or DOCX and wait for a successful upload before leaving the page.
See Documents, flight logs, and maintenance for sharing and attachment procedures.
When contacting support
Provide:
- Suite version and release date from Settings;
- selected drone name and serial number;
- local time and timezone of the problem;
- exact status or error text;
- the action immediately before the problem;
- whether telemetry, map, and each camera were working.
Do not send passwords, tokens, private connection addresses, or confidential customer documents in a normal support message.