Skip to main content

Missions and flight actions

Mission-changing and flight-control actions are available to Administrators and Operators. They also depend on the aircraft state and current telemetry.

Operational control

Use these actions only when authorized, after positively identifying the aircraft, and while following your approved operating procedure. Confirmations reduce accidental clicks but do not validate the flight plan or airspace.

View the current mission​

  1. Select the drone and wait for it to go live. The Suite reads its mission once and draws the route on the map.
  2. In the toolbar above the map, select Mission. The number beside it is the mission's waypoint count; while a mission runs, it shows the step in progress.
  3. Review the panel that opens beside the map: the waypoint count, route distance and highest altitude, then each step in flight order, numbered as on the map.
  4. Select a step to bring it into view on the map and to see its coordinates and command parameters. Selecting a step stops the map following the vehicle.

Altitudes are above Home unless the step says otherwise. Commands without a place of their own, such as starting a video, appear in the list but not on the map.

While a mission runs, the current step is highlighted in the list and on the map, and flown steps are greyed out. Flight data shows the step, the steps remaining and the distance to the current target. The map also draws the track flown since the drone armed, until it next arms.

Read the mission again​

Reopening the panel can reuse the mission already fetched for that drone during the current page session; the panel says when it was read. To read the aircraft again, select Read again while connected. A refresh can leave previous items visible while it runs or if it fails; check the panel's status before treating the route as confirmed.

Save the mission​

Select Save .plan to download <drone-name>-mission.plan, a QGroundControl-compatible file with the mission as last read. It can be opened in a planning tool or sent back with Replace. If a request is running or has failed, check the panel's status before treating the file as current.

Replace the mission​

Use Replace in the Mission panel to send a QGroundControl-compatible .plan file to the selected drone. It replaces the mission stored on the aircraft.

Before you begin​

  • Select and connect to the correct drone.
  • Confirm that you have permission to manage missions.
  • Prepare a valid .plan file no larger than 1 MB.
  • The plan must contain no more than 1,000 mission items.
  • Independently verify coordinates, altitude references, command sequence, and geofence or airspace requirements.

Upload​

  1. In the toolbar above the map, select Mission, then Replace.
  2. Choose the .plan file.
  3. Wait for Mission ready to send and review the items, waypoints, distance and highest altitude.
  4. Select Send to drone.
  5. Keep the drone connected while the Suite prepares storage, sends the items, and waits for the autopilot acknowledgement.
  6. Wait for Mission sent to the drone. The Suite then reads the mission back from the aircraft.
  7. Compare the route on the map and in the Mission panel with the approved plan.

The upload continues if its dialog is closed, but you should keep Drone Control open and monitor progress.

warning

Uploading a mission can replace or invalidate the mission previously stored on the autopilot. Do not navigate away, change drones, or disconnect during upload.

Start a mission​

Start mission appears only when the Suite has a confirmed mission and the aircraft reports the required state.

  1. Confirm the mission on the map.
  2. Confirm that the drone is armed and ready according to your procedure.
  3. Under Flight commands, below the flight data, select Start mission.
  4. Read the confirmation. The action switches the aircraft to AUTO and begins or resumes the mission stored on the autopilot.
  5. Confirm.
  6. Wait for AUTO in Flight data.

If the aircraft disarms, disconnects, or the confirmed mission becomes unavailable, the action is disabled.

Go Here​

Go Here commands a supported ArduCopter multirotor to fly to a selected map position in GUIDED mode.

It is available only when the aircraft is connected, armed, confirmed airborne, has usable GPS and position data, and no other command is pending.

  1. Under Flight commands, select Go Here.
  2. Select the target point on the map, or press Esc to cancel.
  3. Enter the altitude above Home. It starts at the drone's current altitude; the accepted range is 0.5 to 10,000 metres, but your operational limits may be much lower.
  4. Review the target point, distance, and altitude.
  5. Select Send to drone.
  6. Wait for GUIDED in Flight data and the crosshair on the map.
  7. Monitor the flight mode, map, altitude, and aircraft continuously.

If Go Here interrupts an AUTO mission, the Suite may preserve enough context to offer Resume mission.

warning

The selected map point does not check obstacles, terrain clearance, airspace, link quality, or safe stopping distance.

Resume an interrupted mission​

  1. Confirm that Resume mission is available under Flight commands after the guided action.
  2. Confirm the aircraft is still connected, armed, and airborne.
  3. Confirm that the stored mission has not changed.
  4. Select Resume mission and confirm.
  5. Verify the flight mode and expected mission progress.

Resume is not attempted if the mission changed, required context was lost, or the autopilot is configured to restart missions.

RTL​

RTL, or Return to Launch, interrupts the current mode or mission and commands the drone to return according to its autopilot configuration.

  1. Confirm that the drone is connected and confirmed airborne.
  2. Under Flight commands, select RTL.
  3. Read the warning and select Activate RTL.
  4. Wait for RTL in Flight data.
  5. Monitor the aircraft until the operation is safely complete.
danger

RTL does not guarantee a safe route or landing. Home position, rally points, terrain, obstacles, energy state, failsafe settings, and autopilot configuration can all affect the result.

If a control is unavailable​

Check the on-screen explanation. Common causes are:

  • your role does not permit flight control;
  • the drone is disconnected;
  • the drone is disarmed or not confirmed airborne;
  • GPS, position, altitude, or mission data is unavailable;
  • the vehicle type does not support the action;
  • another command or mission operation is still active.